If not right-click on the block where the loco is is select swap logical direction. when Rocrail is in forward position (it shows > on the loco controller) then the loco lights toward the NEXT block should be on. And since it was temporary, totally acceptable by my wife. Otherwise right-click on the block where the loco is is select swap block enter side. On the first day, I set up a semi-circle of track on the kitchen table and ran a locomotive back and forth while changing speed tables and start and max voltages. Extending that use a bit more, I can also use it as a portable DCC system by taking along some EZ Track or UniTrack. My thought was I can use it at the workbench to program and test decoders/locos before going to the main layout. I went with the Sprog over the PR3 or the other proprietary decoder programmers because the Sprog can be used as a command station as well as a programmer. I bought the Sprog in advance of purchasing complex sound decoders as all the CV definitions and their ranges would be available to view and set, instead of keying in each one on my handheld controller while reading a decoder manual. From all I've read here and elsewhere, and seen in the demos, JMRI is the way to go for programming decoders. I did alot of reading on the site noted by Gary as well as the Yahoo groups for Sprog and JMRI. Been off the board what with the holidays and all. Rocview can also be used standalone to plan, create, and edit layouts without a physical connection to the layout.Sorry if this is late. Click supported Command Stations for a list of currently supported Command Stations. Rocrail runs on a computer connected to the layout by one of the standard computer interface setups, and supports many controllers. B is much more complex as it requires additional logic and xponders in the train. The manager should also allow running in opposite directions and direct run overs. The Android based wireless client for Rocrail 'A Model Railroad Control System.' andRoc is a goody for those who have a valid donation key installed on the server. All hardware modules are I2C based and do not need any firmware Rocnetnode handles it all. The Rocnetnode is the software part running on the RasPi and will manage I/O, Servos and throttles. B) train a goes track 2 then swutches to track 3 to the warehouse and stops while train b goes from track 2 to track 1 to loop around a passenger station. Turntable block manager Bug 685753 reported by Rocrail on 42 This bug affects 4 people Bug Description Implement a block manager similar to the FY to make the setup easier. The Rocrail project has developed a protocol based on IP-Multicast Ethernet communication which was chosen for this RasPi solution. Due to Rocrail's client-server architecture, control of a layout from any computer or mobile device on a home network or over the Internet is possible. A) Different trains travel on the same route stopping at stations for x seconds and always apart by 1 block. These programs communicate with each other using TCP/IP, and they do not need to be on the same computer. En la wiki de Rocrail se encuentra la documentación completa, actualizada y guías paso a paso para aprender a utilizar este programa. The software, via the loconet feedback from the DR5088's, also detects the loco being removed from a block and placed in another block or just plain removed. En ningún caso este manual de normas de AENOD pretende ser un manual de Rocrail. Rocrail consists of two programs The Rocrail Server and the Rocview Client. The Rocrail software seems quite flexible, in this area at least. Many have found that running some of the trains on the layout automatically while operating others manually is most enjoyable. Running trains manually or automatically is fully configurable. Rocrail can control a model train layout from one or more computers. Rocrail supports many languages, including English, German, Dutch, French, and many more. It seems Rocrail uses a different approach for the CS2. For MM locos it can be 'ServerDefined' or 'Motorola'. The protocol must be set to 'ServerDefined' for mfx locos. The template is generated from the rocview/ res/message. The address does not matter - but it cannot be 0. I loaded and opened RocRail for the first time and have tried to connect this to the CS2. I connected my CS2 to my home network via an RJ45 cable and entered the IP address into my laptop. Written in C/C++, it is based on the _images_blocks2.jpgwxWidgets class library, and is Open Source. Rocrail uses the unique ID (loco name), not the address, to control locos in the ECoS. I loaded RocRail onto my microsoft note book (windows 10) and am running into beginner issues. Rocrail is an Innovative Model Railroad Control System that runs on Linux, Mac OS X, Raspberry Pi and Windows.
0 Comments
Leave a Reply. |